Login

<A complete kit to construct a solar balloon and two mini-weather stations in order to make comparative measurements.<br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<3760327670016>

<This kit includes all the elements to be associated with the use of the solar balloon but can also be used alone for the reading of parameters of the atmosphere: temperature, humidity, pressure but also measurements of volatile organic compounds and CO2 content. In the box, you will find: a user guide, an electronic weather kit consisting of a microcontroller (Arduino), altitude, air quality, temperature and pressure sensors, LCD screen, microSD card and connectors required for assembly.<br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<3760327670030>

<The air quality kit includes all the elements to carry out numerous measurements concerning air quality. These measurements can be compared to those of your Approved Air Quality Monitoring Association! </br> You will be able to measure the temperature and humidity of the air, but also volatile organic compounds and the content of CO, CH4 and NO2. You will also be able to quantify fine particles in suspension of sizes PM 10, 2.5 and 1. </br> Contents: - a user guide, - an electronic kit composed of a microcontroller (Arduino) and its Grove shield - HM3301 sensor: fine particles (PM10, 2.5 and 1) - MICS6814 sensor: gas (NO2, CH4, CO), - DHT11 sensor: humidity and temperature, - a monochrome Grove LCD screen - a microSD card - OpenLog microSD reader - microSD-USB adapter - USB cable 30cm<br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<3760327670054>

<Discover the power of the sun with the Solar Oven! Reach temperatures up to 150°C with this kit. The oven is made of poplar wood grown in French eco-managed forests, itself machined with a laser cutter in France. The kit contains a programmable station that measures the temperature inside and outside the oven, as well as visible brightness, ultraviolet and infrared. The station is composed of an Arduino Uno or Micro:bit card, at your own choice. <br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<3760327670085>

<The connected plant kit includes the elements for monitoring soil moisture and light and controlling the automatic watering of a plant. <br> Content: <br> - a user guide <br> - an electronic kit composed of a microcontroller (Arduino Uno) <br> - a Grove shield <br> - light sensor <br> - soil moisture sensor <br> - a monochrome Grove LCD screen <br> - automatic watering set composed of a Mosfet module, a water pump and a 6V power supply <br> - USB cable <br> <br> Manufacturer: Vittascience <br> Reference: 3760327670245 <br><br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<3760327670238>

<CO2 KIT - Arduino version CO2 measurement kit comprising: <br> - an arduino Uno card <br> - a Grove shield <br> - a Neopixel RGB led <br> - an SCD30 Sensirion sensor <br> - power supply <br> - batteries <br> - USB cable <br> <br> Resource available to program your sensor <br><br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<3760327670177>

<A complete kit to construct a solar balloon and two mini-weather stations in order to make comparative measurements.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<3760327670023>

<This kit includes all the elements to be associated with the use of the solar balloon but can also be used alone for the reading of parameters of the atmosphere: temperature, humidity, pressure but also measurements of volatile organic compounds and CO2 content. In the box, you will find: a user guide, an electronic weather kit consisting of a microcontroller (micro:bit), altitude, air quality, temperature and pressure sensors, LCD screen, microSD card and connectors required for assembly.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<3760327670047>

<The air quality kit includes all the elements to carry out numerous measurements concerning air quality. These measurements can be compared to those of your Approved Air Quality Monitoring Association! </br> You will be able to measure the temperature and humidity of the air, but also volatile organic compounds and the content of CO, CH4 and NO2. You will also be able to quantify fine particles in suspension of sizes PM 10, 2.5 and 1. </br> Contents: - a user guide, - an electronic kit composed of a microcontroller (Arduino) and its Grove shield - HM3301 sensor: fine particles (PM10, 2.5 and 1) - MICS6814 sensor: gas (NO2, CH4, CO), - DHT11 sensor: humidity and temperature, - a monochrome Grove LCD screen - a microSD card - OpenLog microSD reader - microSD-USB adapter - USB cable 1m<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<3760327670061>

<Discover the power of the sun with the Solar Oven! Reach temperatures up to 150°C with this kit. The oven is made of poplar wood grown in French eco-managed forests, itself machined with a laser cutter in France. The kit contains a programmable station that measures the temperature inside and outside the oven, as well as visible brightness, ultraviolet and infrared. The station is composed of an Arduino Uno or Micro:bit card, at your own choice. <br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<3760327670092>

<3, 2, 1 GO!<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<3760327670108>

<3, 2, 1, Go! Launch your students into a futuristic race using this kit. The Course LED / LED race kit consists of the following elements for the 150 led version. Micro: bit card Shield Grove or Bitmaker 150 neopixel leds strip 5m Grove Speaker Pushbutton USB mains socket 1M USB cable Printed and bound educational booklet Downloadable digital resources<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<3760327670115>

<3, 2, 1, Go! Launch your students into a futuristic race using this kit. The class pack consists of 6 Course LED kits with the addition of a strip of 150 neopixel 5m LEDs. 18 micro: bit card 6 Grove or Bitmaker shield 6 strips 30 neopixel leds 1m 1 strip 150 neopixel leds 5m 6 Grove Speaker 12 Push button 6 USB mains socket 6 USB cable 1M 1 Printed and bound educational booklet Downloadable digital resources<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<3760327670122>

<The connected plant kit includes the elements for monitoring soil moisture and light and controlling the automatic watering of a plant. <br> Content: <br> - a user guide <br> - an electronic kit composed of a microcontroller (micro: bit) <br> - a Grove shield <br> - light sensor <br> - soil moisture sensor <br> - a monochrome Grove LCD screen <br> - automatic watering set composed of a Mosfet module, a water pump and a 6V power supply <br> - USB cable 1m <br> <br> <br> Available for preorder - delivery September 2021 <br> <br> <br> Manufacturer: Vittascience <br> Reference: 3760327670245 <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<3760327670245>

<Explore Mars with your robot! <br> This kit includes all the elements to discover and learn programming around a robot. Complete several missions using the detailed booklet. <br> Content: <br> - an activity booklet <br> - a Maqueen robot <br> - a micro: bit card <br> - an infrared remote control <br> - an extension for robot: gripper and servomotor <br> - a track for a line follower robot <br> <br> <br> Available for preorder - delivery September 2021 <br> <br> <br> Manufacturer: Vittascience <br> Reference: 3760327670252 <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<3760327670252>

<Artificial Intelligence discovery kit around the micro: bit card. <br> Several activities are offered in the booklet provided. <br> <br> Kit composition: <br> - an activity booklet <br> - a micro: bit card <br> - a HUE HD camera <br> - a 1m usb cable <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<3760327670313>

<CO2 KIT - micro: bit version CO2 measurement kit comprising: <br> - a micro: bit card <br> - a Grove shield <br> - a Neopixel RGB led <br> - an SCD30 Sensirion sensor <br> - power supply <br> - batteries <br> - USB cable <br> <br> Resource available to program your sensor <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<3760327670184>

<The connected plant kit includes the elements for monitoring soil moisture and light and controlling the automatic watering of a plant. <br> Content: <br> - a user guide <br> - an electronic kit composed of a microcontroller (NUCLEO-WB55RG card) <br> - a Grove shield <br> - light sensor <br> - soil moisture sensor <br> - a monochrome Grove LCD screen <br> - automatic watering set composed of a Mosfet module, a water pump and a 6V power supply <br> - USB cable 1m <br> <br> <br> <br> Manufacturer: Vittascience <br> Reference: 3760327670269 <br><br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br>>

<3760327670269>

<Explore Mars with your robot! <br> This kit includes all the elements to discover and learn programming around a robot. Complete several missions using the detailed booklet. <br> Content: <br> - an activity booklet <br> - an Alphabot robot <br> - a Nucleo WB55RG card <br> - an infrared remote control <br> - a track for a line follower robot <br> <br> <br> Manufacturer: Vittascience <br> Reference: 3760327670276 <br><br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br>>

<3760327670276>

<Measure and optimize indoor air quality using this comprehensive kit. <br> Assemble your alert box including: <br> - an ST NUCLEO-WL55 board equipped with an STM32 microcontroller with LoRa <br> - a Grove shield<br> - a Neopixel RGB led <br> - an LCD screen <br> - an SCD30 Sensirion sensor (CO2 - temperature - humidity) <br> - USB cable <br> - a 220V to USB mains adapter <br> - an accompanying booklet <br> <br> Manufacturer: Vittascience <br> Reference: 3760327670344<br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br>>

<3760327670344>

<With the Solar Balloon Kit, discover the unique sensation of flying a DIY object. The kit contains all the material and instructions necessary for the construction of a solar balloon 4 meters in diameter, flying thanks to the energy of the sun and carrying up to 1 kg of payload. This kit can also be used as a refill for the Weather Balloon project, that is to say that the balloon carries a weather station. Solar Balloons can fly many consecutive times but can not be deconstructed.<hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<3760327670009>

<Discover the power of the sun with the Solar Oven! Reach temperatures up to 150°C with this kit. The oven is made of poplar wood grown in French eco-managed forests, itself machined with a laser cutter in France. The kit contains a programmable station that measures the temperature inside and outside the oven, as well as visible brightness, ultraviolet and infrared. The station is composed of an Arduino Uno or Micro:bit card, at your own choice. <br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<3760327670078>

<Arduino Uno Rev3 Board with an Arduino-USB connecting computer cable.<br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<ARDUNOR3>

<Arduino Nano card </br> Tech Specs : </br> Microcontroller -ATmega328 <</br> Architecture - AVR </br> Operating Voltage - 5 V </br> Flash Memory - 32 KB of which 2 KB used by bootloader </br> Analog IN Pins - 8 </br> EEPROM 1 KB </br> Input Voltage - 7-12 V </br> Digital I/O Pins - 22 (6 of which are PWM) </br> PWM Output - 6 </br> Power Consumption - 19 mA </br> PCB Size - 18 x 45 mm </br> Weight - 7 g </br><br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<ARDNANO>

<<br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<AZ-D1R32>

<Discover the new version of the micro: bit card! </br> More power and functionality thanks to integrated sensors: - microphone, </br> - loudspeaker, </br> - bluetooth antenna, </br> - tactile logo </br> This new version of the card also allows the activation of an "energy saving" mode. </br> Supplied with 2 batteries, a battery connector and a micro-USB cable. </br> Available for sale in November. </br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<MBV2>

<Dedicated pack for the classroom containing 10 micro: bit V2 cards, 10 micro-USB cables and 10 boxes for batteries provided. Available for sale in November.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<MBclubV2>

<The famous programming card, with battery, battery connector and micro-USB cable.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<MB>

<Pack of 10 micro-bit programmable cards with batteries, battery connectors and micro-USB cables.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<MB224-US>

<Raspberry Pi Zero WH card with a 40-pin GPIO connector. Processor: ARM1, Broadcom BCM2835, Single-core 1GHz Memory: 512 MB Connections: 1x micro SD card, 1x mini HDMI, 1x micro USB OTG, 1x CSI, 1x GPIO Communication: WIFI 802.11b / g / n WLAN, Bluetooth BLE 4.1<br><br><hr>This product is compatible with the following card(s) : <br> - QuickPi and RaspberryPi<br>>

<PIZEROWH>

<The Raspberry Pi 4 Model B is the latest product in the Raspberry Pi family of computers. It offers increased processor speed, multimedia performance, memory and connectivity compared to the Raspberry Pi 3. Processor: 1.5 GHz Cortex-A72 64-bit quad-core SoC, Broadcom BCM2711, ARM v8 Memory: 4 GB Connections: 2x USB 2.0, 1x micro SD, 2x USB 3.0, 1x MIPI DPI, 1x GPIO, 2x micro HDMI, 1x MIPI CSI Communication: WIFI 802.11b / g / n / ac 2.4 GHz and 5.0 GHz, Gigabit Ethernet, Bluetooth 5.0, BLE Power supply: 5V DC via GPIO, 5V DC via USB-C<br><br><hr>This product is compatible with the following card(s) : <br> - QuickPi and RaspberryPi<br>>

<PI4-4GB>

<The Calliope Mini card is a microcontroller with many integrated functions. This card is ideal for learning and discovering programming. It has a flash memory allowing the storage of 25 programs. <br> <br> Components integrated into the Calliope Mini card: <br> - 5x5 LED matrix <br> - 1 RGB led <br> - 1 speaker <br> - 2 buttons A and B <br> - 4 ports P0, P1, P2, P3 <br> - 2 power supply terminals + and - <br> - 1 mixed sensor: acceleration, compass, motion detectors <br> - 1 light sensor (through the LEDs of the matrix) <br> - 1 temperature sensor <br> - 1 microphone <br> - 1 radio and bluetooth antenna <br> - 2 Grove ports <br> - plugs to connect two motors <br> - reset button <br> <br> Power supply via micro-usb socket or power supply unit supplied. <br> <br> Card delivered with: USB cable, battery holder, 2 AA batteries, 1 rubber band, stickers <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<0742832906043>

<NUCLEO-WB55RG programmable card equipped with an STM32 microcontroller with Bluetooth BLE.<br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<WB55RG>

<Small and full of capabilities, this board is a great medium for learning Python programming in high school and block programming in middle school. <br> Its color screen displays messages, graphics and identifies programming errors. <br> The Galaxia communicates in a local network with other Galaxia cards. It can also be programmed as a web server or as a WiFi access point. <br> <br> Components built into the Galaxia board: <br> - 1 ESP32-S2 Wi-Fi module (240MHz) <br> - 1 color screen 128 x 160 pixels <br> - 1 RGB LED <br> - 1 audio input/output <br> - 2 buttons A and B <br> - 4 touch buttons <br> - 1 accelerometer <br> - 1 magnetometer <br> - 1 brightness sensor <br> - 1 ambient temperature sensor <br> - 2 Grove ports <br> - 1 connector for micro:bit <br>accessories <br> Power supply via micro USB connector. <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<GALAXIATHINGZ>

<Programmez vos objets connectés en Scratch, Blockly ou Python avec ce kit extensible constitué d’un Raspberry Pi Zero WH connectable en wifi, bluetooth ou usb, et d’une carte qui regroupe 10 capteurs, 5 actionneurs, et 4 ports Grove pour l’étendre sans limites. <br><br> Adapté au collège et lycée (SNT et NSI), il se programme depuis son navigateur, qui aide &agrave; comprendre ses erreurs grâce &agrave; un mode pas &agrave; pas en simulation complète ou connecté &agrave; la carte. <br><br> Ce kit est con&ccedil;u par l’association France-ioi pour accompagner des parcours de découverte constitués de nombreux exercices validés automatiquement, qui permettent d’apprendre &agrave; programmer un avertisseur de recul, une alarme anti intrusion, un animal connecté, un applaudimètre, et d’imaginer vos propres projets sans limites. <br><br> Les ports d’extension Grove permettent d’ajouter de nombreux capteurs et actionneurs Grove disponibles dans le commerce, comme des servomoteurs ou sondes de température, capteur d’humidité etc. (non fournis) <br><br> Le kit est livré déj&agrave; assemblé et pr&#xEA;t &agrave; l’usage.<br> Retrouvez plus de détails et de nombreuses ressources sur le site <a href="http://quick-pi.org/">quick-pi.org</a>.<br><br><hr>This product is compatible with the following card(s) : <br> - QuickPi and RaspberryPi<br>>

<KQUICKPI>

<Grove Starter Kit for Arduino is one of the best Arduino Starter Kit for beginners. It includes one Arduino compatible shield - Base shield and 14 additional Arduino sensors and accessories. You can build any Arduino project you like with this Grove Starter Kit.<br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<110060024>

<Resulting from the collaboration between Arduino and Seeedstudio, the Arduino Sensor Kit is a card expansion module suitable for education and grouping together several sensors. <br> This kit contains a shield for an Arduino Uno board and 10 Grove modules: <br> - Red LED <br> - buzzer <br> - oled display <br> - push button <br> - potentiometer <br> - sound sensor <br> - light sensor <br> - DHT11 temperature and humidity sensor <br> - BMP280 pressure and temperature sensor <br> - 3-axis accelerometer <br><br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<103030375>

<Ce kit comprend : 1 shield Grove pour micro:bit 1 capteur d'angle rotatif Grove 1 haut-parleur Grove 1 télémètre à ultrasons Grove 1 capteur de lumière v1.2 Grove 1 guirlande de LED waterproof WS2812 (1 mètre, 30 LED) Grove 1 capteur de mouvements Grove 1 écran d'affichage numérique Grove (4 chiffres) 1 LED rouge Grove 1 câble micro-USB 48 cm 1 manuel pour 12 projets 10 câbles avec connecteurs à pince crocodile 7 câbles Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<110060762>

<This starter kit includes: <br> - a Raspberry Pi4 2GB card <br> - an Okdo protection box <br> - a 32 GB NOOBS microSD card <br> - an official USB-C power supply <br> - a micro-HDMI to HDMI cable length 1m <br> - a set of 4 heat sinks <br><br><br><hr>This product is compatible with the following card(s) : <br> - QuickPi and RaspberryPi<br>>

<KITPI42GB>

<Kit for carrying out measurements in a pond or pond. <br> <br> Composed of an Arduino board, a Grove shield, a waterproof temperature sensor, a turbidity sensor, an openlog for data logging and a pH probe. <br> <br> Delivered with the necessary connectors for assembly. <br><br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<3760327670283>

<Kit for carrying out measurements in a pond. <br> <br> Composed of a micro: bit card, a Grove shield, a waterproof temperature sensor, a turbidity sensor, an openlog for data recording and a pH probe. <br> <br> Delivered with the necessary connectors for assembly. <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<3760327670290>

<Shield Grove for micro:bit<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<103100063>

<BitMaker is a credit card-sized extension board designed for connecting micro:bit with Grove modules. It acts as a bridge for micro:bit and our Grove modules system.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<114991848>

<Input/Output micro:bit shield<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<KITRO5601B>

<Simon:says game for micro: bit. Specially developed for a micro:bit card with a buzzer, 4 capacitive keys and 4 RGB leds (NeoPixel type) Supplied with 4 rubber pad feet.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<PPMB00111>

<Designed for use with a micro: bit V1 or V2 card, this ring of 60 programmable LEDs has a microphone, a buzzer and a RTC circuit. <br> This extension will be ideal for carrying out your clock, meter or sound level meter project. <br> Powered by 3 AA batteries not included. <br> Brooches: <br> - P8: leds <br> - P0: micro <br> - P14: buzzer <br> - P19 and P20: RTC <br> P1 and P2 available with solder pads.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<Kitro5672>

<Comes fully-assembled and ready to use. BME280 temperature, pressure, and humidity sensor TCS3472 light and colour sensor MEMS microphone<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<PIM355>

<Arduino Grove Shield<br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<103030000>

<Shield Arduino grove SD V4<br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<103030005>

<This Grove Shield module is an interface board for easily, quickly and without soldering the sensors and actuators with Grove connectors (4 wires in 1 with keying) to an Arduino Nano compatible board.<br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<103100124>

<Shield for Arduino board allowing the control of two direct current motors in both directions. It will be perfect for creating a motorized robot. <br> This shield has a jumper to allow power to the Arduino board via the Vin port as well as indication leds. <br> This module can be attached to the Grove shield. The connection of the power supply unit and the motors is made using screw terminal blocks. <br> Motor power supply: 5 to 28 V <br> Maximum current: 3 A <br> <br><br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<2503>

<The TI-Innovator Hub, developed by Texas Instruments is an autonomous and portable microcontroller. It can be connected to the TI 83 Premium Edition CE calculator. <br> Equipped with various input and output ports for Grove-type sensors, this module also has a red-green-blue (RGB) LED, a red LED, a light level sensor and of a loudspeaker. <br> <br> Breadboard connector with 20 labeled pins <br> I²C Port <br> Mini USB port (DATA port for connection to a TI graphing calculator or computer running TI-Nspire™ CX software) <br> Micro-USB Port (POWER Port for connecting to an external power source) <br> Powered by TI LaunchPad™ MSP-EXP432P401-ET Board <br>>

<03243480105682>

<Maqueen robot for micro:bit board<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<ROB0148>

<Forklift for Maqueen robot to be fixed on the frame using the screws and spacers provided. Includes all aluminum alloy elements as well as the 9g servo motor to be connected to one of the pins.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<ROB0156-F>

<Clamp for Maqueen robot to be fixed on the frame with the screws and spacers provided. <br> Includes all aluminum alloy elements as well as the 9g servo motor to be connected to one of the pins.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<ROB0156-B>

<Mechanical shovel for Maqueen robot to be fixed on the frame using the screws and spacers provided. Includes all aluminum alloy elements as well as the 9g servo motor to be connected to one of the pins.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<ROB0156-L>

<Move Mini Buggy robot for micro:bit board<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<RBUGGY>

<Buldozer Extension for Move Mini Buggy robot<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<MBUGGYBULL>

<Alphabot2 robot for Arduino board <br> <br> This chassis has the following components: <br> - 2 geared motors <br> - an OLED display <br> - 4 RGB LEDs <br> - a buzzer <br> - an IR receiver <br> - an ultrasonic obstacle detector <br> - IR proximity sensors <br> - line trackers <br> <br> Delivered with: <br> - infrared remote control <br> - USB cable - microUSB <br> <br> Power supply via 2 batteries format 14500 - 3.7V <br><br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<12911>

<Robot for micro: bit card (not included). <br> This robot has an electronic card incorporating a buzzer, 2 line tracking sensors, 4 addressable LEDs. <br> It has two Grove ports to add a supplied ultrasonic sensor. <br> Sold as a kit to assemble with screws and screwdrivers. <br> Batteries not included. <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<114991884>

<This Bit-Mecanum robot has 'mecanum' wheels allowing it to move in all directions. <br> Programmable by its micro: bit card (supplied with), it is also possible to control it using a second card used as a remote control. <br> It's up to you to imagine the most difficult routes! Alimentation : batterie 3,7V - 18650 (non fournie)<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<110090322>

<Robotic Arm Kit for micro:bit board<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<RBRAS>

<Game Pad Extension for micro:bit board<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<DFR0536>

<This BitPlayer controller for micro: bit card (not supplied) has a 2-axis joystick, 6 programmable buttons (L and R + A, B, C and D), a buzzer and a vibrator. <br> It also incorporates a Grove I2C port to add an LCD screen. <br> You can use this controller to program your own game with the micro: bit card or use it as a remote control for your robot! <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<114991857>

<Aluminum crawler frame including 2 motors. It is ideal for your robot projects. <br> The kit includes: <br> - aluminum frame <br> - 2 tracks <br> - 4 training wheels <br> - support block for 18650 battery (supplied without power supply) <br> - screws <br> <br> Programming recommended by Arduino board and motor control. <br><br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<ROB0153>

<Programmable robotic hand via a micro: bit card. Equipped with several modules: <br> - ultrasonic distance sensor <br> - color sensor <br> - 2 RGB leds <br> - sound sensor <br> - buzzer <br> Powered by a 3.7 V battery or from the mains (6V, 5A) <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<HIW-UHA>

<PVC track for line follower robot on the theme of the planet Mars. Track dimension: 1.24 x 2.04 m<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<3760327670320>

<Track for line follower robot on the theme of the planet Mars. <br> <br> Track size: 102 x 62 cm <br> <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<3760327670306>

<Drone Tello (DJI-Ryze) programmable using Vittascience interfaces. <br> Controllable via Wi-Fi from the smartphone, or from the computer. <br> <br> Comes with spare propeller and a battery <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<Tello>

<Support for 3.7V DC 16340 battery designed for the Micro robot: Maqueen. This module also includes a charging circuit via microUSB with indication leds.>

<FIT0611>

<>

<MBT0011>

<The TI-Innovator Rover is a programmable robot for Texas Instruments graphing calculators and the TI-Innovator Hub.<br> <br> User of the TI-83 Premium CE Edition Python calculator, use the Rover to carry out new missions! <br> The TI-Innovator Rover is powered by rechargeable battery. <br> It has 2 integrated motors as well as a color detector, a gyroscope, a marker holder and a motion detector. <br>>

<03243480105811>

<Écran LCD Grove 32 caractères (16x2) noir sur fond jaune<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<104020113>

<RGB LCD Display Grove 32 characters<br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<104030001>

<OLED Display Grove 128*64<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<104030008>

<4-Digit Display Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<104030003>

<Led Bar Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<104020006>

<This Grove - LED Pack includes 4 kinds of different colors of LED which are red, green, blue, and white. The LED can be easily plugged on the LED Pack, and there is a spin button that can control the luminance of the LED. The interface of this LED module is the Grove interface, you are strongly recommended to use Grove cable and Grove shield for getting started. If the LED does not light up, try rotating the potentiometer with a screwdriver to increase the brightness. <br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<104020228>

<Variable Color LED Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020472>

<Grove module consisting of an addressable RGB LED. <br> Possibility of connecting several modules together via the presence of solder pads.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<104020169>

<RGB 20 Neopixel LED Ring Grove <br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<104020168>

<RGB 30 Neopixel LED Strip Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<104020108>

<5 meter NeoPixel RGB tape equipped with 150 LEDs. These 150 LEDs are connected in series and communicate with a microcontroller via a 1-pin serial output.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<WS2812B5M30LW67>

<RGB LED Matrix 8*8 Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<105020073>

<Red LED Matrix 8*8 Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<104020089>

<The Lamp: bit lamp from Kitronik simulates the lighting of a street lamp. This module works exclusively with a micro: bit card which is fixed with the screws provided. It also includes a phototransistor for measuring the brightness of the room in which it is used. It is perfect to simulate public lighting with an automatic ignition.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<LAMPBIT>

<Traffic Light Kitronik<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<STOPBIT>

<Angular servomotor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<316010005>

<Ce servomoteur (couple 1,5 Kg.cm) bénéficie d'une rotation continue (il ne dispose pas de butée). Dès lors, il vous sera possible de le piloter en sens de rotation et en vitesse au moyen de signaux PWM. <br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<FS90R>

<The Kitronik Access: bit barrier simulates the opening of an automatic barrier. This module works exclusively with a micro: bit card which is fixed with the screws provided. It includes a servomotor and a programmable buzzer. The LEDs on the micro: bit card located on the front can be used to simulate additional information such as a stop, a validated passage arrow, etc. This Access: bit also has a support compartment for 3 batteries (type AA).<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<ACCESSBIT>

<The Servo Kit for micro:bit makes it easy to connect up three servomotors from your micro:bit. The kit is supplied with the servo board, three servos, a battery cage, and alligator/crocodile leads.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<SKU00075>

<Grove - I2C Motor Driver(L298P) is a common-use motor driver for stepping motor and servo motor. It embeds an STM32 chip for burning the code to control the motor driver. 2-channel output: able to support 1A current on each channel, max 2A current; Need 6V-12V DC voltage input. User LED: green LED on for the clockwise direction and red LED on for the anti-clockwise direction for each channel.<br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<105020093>

<Relay Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<103020005>

<A light, small size, high efficiency, low consumption and low noise water pump. <br> Note: Please do not test for a long time without load, the inside is made of plastic sheets, can not suck the impurities. <br> <br> In order to avoid any risk of short-circuit, immerse only the sealed part provided for this purpose.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<PPMB00117>

<Set consisting of a water pump, a Grove mosfet module and a 6V battery box. <br> <br> This pack will be suitable for automatic watering applications using an Arduino or micro: bit board. <br> The power delivered to the pump, and therefore the flow rate, can be adjusted using the Vittascience programming blocks.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<3760327670221>

<Min Fan Grove <br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<108020021>

<Vibration Motor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<105020011>

<This Grove water atomizer module is perfect for developing an air humidifier. Based on an ultrasonic transducer with control card connects to a digital output of an Arduino type microcontroller card or compatible. <br> <br> This module is connected to a digital output of the Grove Base Shield or the Mega Shield via a 4-conductor cable included. <br> <br> In order to avoid any risk of short-circuit, immerse only the sealed part provided for this purpose. <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020090>

<Grove - Electromagnet<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020073>

<Buzzer Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<107020000>

<Speaker Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<107020001>

<MP3 module Grove<br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<107020069>

<The OpenLog data acquisition module is an open source data logger. Power on this device and it will start recording serial data at 9600 bps. <br> OpenLog firmware is open source and is based on sdfatlib by Bill Greiman. <br> OpenLog currently supports microSD FAT16 and FAT32 cards (tested up to 16 GB). <br> Comes with a 128 mb microSD card.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<OPENLOG>

<MicroSD reader<br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<SDSPI>

<Serial Bluetooth Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<113020008>

<This HC05 Bluetooth module allows you to add a Bluetooth link on your microcontroller projects (communication via TTL serial). This module is delivered with a Grove adapter, compatible with the Grove shield for Arduino or micro: bit.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<HC05>

<This HM10 Bluetooth module allows you to add a Bluetooth link to your microcontroller projects (communication via TTL serial). <br> This module is delivered with a Grove adapter, compatible with the Grove shield for Arduino or micro: bit. <br> <br> Works with iOS <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<HM-10>

<This remote control includes 21 buttons including 4 dedicated to directions. It can be used to control a robot or any other object with an infrared receiver. Power supply: 3 VDC via CR2032 battery included Buttons: 21 Frequency: 38 kHz Wavelength: 940 nm Coding: NEC compatible<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<IRC01>

<Infrared emitter Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020026>

<Infrared receiver Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020016>

<GPS receiver Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<113020003>

<Real-time clock RTC Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020013>

<NFC reader 13.56 MHz Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<113020006>

<RFID reader 125 kHz Grove<br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<113020002>

<Radio 433 MHz Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<113060000>

<LoRa 868 MHz transmitter / receiver for creating a long-range wireless link for the creation of connected objects. <br> <br> Module is based on an ATmega168 and an energy efficient RFM95. <br> <br> Power supply: 3.3 and 5 Vdc <br> <br> Consumption: <br> - in emission: 28 mA <br> - in reception: 20 mA <br> - at rest: 8.4 mA <br> <br> Interface: UART <br> <br> Frequency: 868 Hz <br> <br> Maximum transmission power: 100 mW (+20 dBm) <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<113060006>

<This module allows you to emmit and receive data from a board to another.</br>During flight, you can have the data in real time from the ground.<br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<317990024>

<NFC reader in Grove format for reading and writing NFC badges and cards with a frequency of 13.56 MHz.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<ANT7-T-M24SR64>

<Module émetteur et récepteur WiFi basé sur un ESP8285 avec antennes intégrées. <br> <br> Fonctionnalités Wi-Fi : <br> - 802.11 b/g/n 2.4GHz <br> - WiFi Direct (P2P) et Soft-AP (partage d'accès) <br> - WEP, WPA / WPA2, TKIP, AES, et WAPI <br> - Protocoles TCP/IP <br> <br> Leds d'indications intégrées <br> Deux boutons (reset et mode boot UART) <br> <br> Ce module conviendra parfaitement pour envoyer vos données mesurées sur un serveur distant ou pour contrôler votre drone Tello.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - Arduino Uno and Nano<br>>

<113020011>

<Ultrasonic sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020010>

<Infrared distance sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020042>

<Piezo vibration sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020031>

<Sound sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020023>

<Current sensor based on an INA219B circuit. Allows direct current measurement up to 3.2 A with a resolution of 0.8 mA (up to 26 VDC). Delivered already welded with grove connectors.<br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<INA219B>

<Moisture sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020008>

<Water sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020018>

<Arduino and micro: bit compatible pH probe for measuring a pH between 0 and 14 at a temperature between 0 and +60 ° C. This probe delivers an analog voltage as a function of the PH. <br> Probe delivered with two buffer solutions (4.0 and 7.0 PH) allowing a two-point calibration. <br> In order to avoid any risk of short-circuit, immerse only the sealed part provided for this purpose. <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<SEN0161V2>

<Rain meter Grove <br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<LEXCA001>

<Wind meter Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<LEXCA003>

<This connection module allows you to connect the rain gauge, the anemometer and the wind vane to an Arduino or micro: bit board via Grove cables. <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<DEV-LEX2>

<This turbidity sensor is used to determine the quantity of particles in a liquid. <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020752>

<Color sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020341>

<Line finder grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020172>

<The Grove motion sensor module will detect the slightest movement nearby in order to activate the GIS output in the high state. This module has a detection range of up to 12m.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020793>

<Light sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020132>

<Visible, infrared and UV light sensor Grove - SI1145<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<SI1145>

<UV sensor with Grove connector <br> Detection spectrum 200 nm to 400 nm. <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020043>

<Gas sensor Grove - MQ135<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<MQ135>

<CO2 and VOC sensor Grove - SGP30<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020512>

<This gas sensor is an environment detection sensor based on the 32-bit Value-line ARM® technology, having an I2C interface as well as 4 separate sensors which make it possible to detect many gases (Nitrogen dioxide, Monoxide of carbon, Ethanol, Hydrogen, Ammonia, Methane, Propane and Iso-butane). Please note that the heating time is required for proper operation of the sensor.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020820>

<Dioxygene O2 sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101990680>

<Carbon dioxyde CO2 sensor Grove - MH-Z16<br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020067>

<Grove sensor measuring CO2 concentration, temperature and observation at the same time. This module is based on a Sensirion SCD30 and incorporates non-dispersive infrared measurement technology. <br> <br> This sensor is ideal for your environmental projects (air quality measurement, monitoring system, weather station, etc.) <br> Measuring range: <br> 0 to 10,000 ppm <br> 0 - 50 ° C <br> 0 to 100% RH <br> <br> Accuracy: <br> 30 ppm <br> 0.5 ° C <br> 2% RH <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020634>

<Sensirion SCD30 sensor measures both CO2 concentration, temperature and humidity. This module incorporates non-dispersive infrared measurement technology. <br> This sensor is ideal for your environmental projects (air quality measurement, monitoring system, weather station, etc.) <br> Measuring range: <br> 0 - 10,000 ppm <br> 0 - 50 ° C <br> 0 - 100% RH <br> <br> Accuracy: <br> 30 ppm <br> 0.5 ° C <br> 2% RH <br> <br> Manufacturer: Sensirion <br> Reference: SCD30 <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<SCD30>

<Fine particles sensor with connecting cables to expand the activity on air quality. More pertinent on the ground than when in the air, this sensor must remain stable for a long period of time to offer interesting measurements.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020012>

<PM laser sensor Grove - HM3301<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020613>

<T°, pressure and altitude sensor Grove - BMP280<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<BMP280>

<T° sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020015>

<This Grove waterproof temperature sensor is based on the DS18B20 circuit with a measuring range of -55 ° C to + 125 ° C. <br> In order to avoid any risk of short-circuit, immerse only the sealed part provided for this purpose. <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101990019>

<High T° sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<111020002>

<This Grove compatible DHT11 temperature and humidity sensor uses a NTC thermistor and a capacitive sensor and delivers a digital output. <br> <br> To be connected to a Grove analog output. <br> Does not work below 0 ° C <br> <br> Measuring range: <br> temperature: 0 ° C to 50 ° C (± 1 ° C) <br> humidity: 20 to 90% relative humidity (± 5%) <br> <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020011>

<This Grove compatible DHT22 temperature and humidity sensor uses a NTC thermistor and a capacitive sensor and delivers a digital output. <br> <br> To be connected to a Grove analog output. <br> Measuring range : <br> temperature: -40 ° C to 80 ° C (± 0.5 ° C) <br> humidity: 5 to 99% relative humidity (± 2%) <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020019>

<Temperature and humidity sensor with Grove connectors Accuracy: ± 0.3 ° C / ± 2% humidity<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020212>

<Grove-Infrared temperature sensor is a non-contact temperature measure model. Temperature measure range : -10 ~ 100 ° C Measure accuracy : ± 2 ° C Nominal measure distance : 9CM<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020062>

<Gesture sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020083>

<Tilt sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020025>

<Magnetic switch Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020038>

<<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<110020248>

<Grove - Round Force Sensor FSR402<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020553>

<Detects skin conductance at finger level with electrode straps Used to detect strong emotions. Galvanic skin response refers to changes in sweat gland activity that reflect the state of our emotional state, otherwise known as emotional arousal. Grove connector<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020052>

<Pulse Sensor<br><br><hr>This product is compatible with the following card(s) : <br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<MFREQCARD>

<Heartbeat sensor with Grove connectors. <br> This sensor consists of a clip to be attached to the earlobe or to the fingertip. <br> <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020033>

<<br><br><hr>This product is compatible with the following card(s) : <br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<11003>

<Connection module with screw terminal block to access the 4 Grove pins <br> Manufacturer: Seeedstudio <br> Reference: 103020007 <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<103020007>

<Distance sensor based on a VL53L0X and allowing the detection of an object in a range of 30 to 1000 mm.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020532>

<Push Button Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<111020000>

<LED Button Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<111020045>

<Touch Sensor Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020037>

<Touch Keypad Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020636>

<Thumb Joystick Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020028>

<Rotary Angle Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<111020001>

<Slide Potentiometer Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020036>

<Switch Grove<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<101020004>

<Grove module limit switch with blade.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<102020143>

<Apparence et amusement, rendent des accessoires plus sûrs. Matériaux de silicone de sécurité de catégorie comestible. Protégez micro:bit de l'usure externe. Cinq couleurs pour votre choix.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<KITTENBLEU>

<Transparent protective case for micro: bit card 4 x M3 nylon screws 4 x M3 nylon nuts 1 x backplate 1 x front plate 2 x intermediate plates<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<MIPRO>

<I2C Hub Grove is an extension Grove module for connecting multiply I2C devices to Grove Base Shield. It can use with Universal 4 Pin to X2 4 Pin cable and connects up to 7 I2C divices which may cover most developing purpose.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<103020006>

<The Grove I2C hub is a Grove module used to connect multiple I2C devices to the shield. <br> With this power strip, you can connect up to 5 elements!<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<103020272>

<Jeu de 10 câbles pinces crocodiles<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - Arduino Uno and Nano<br>>

<LOT10CROCO>

<Grove 30 cm cable with key. Delivered by x5<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<110990040>

<Grove 50 cm cable with key. Delivered by x5<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<110990038>

<Ce câble vous permettra de connecter facilement un module Grove à une carte Arduino sans utiliser de shield. <br> Câble de 20 cm de long.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<110990210>

<Pack of 5 Grove-Female Conversion Cable<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<110990028>

<Grove cable 20 cm long for the connection of two servomotors. <br> This cable is used to connect one or two FS90R continuously rotating servomotors.<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<110990057>

<1m USB cable for power supply and data transfer on a microbit card<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<USB1M>

<30 cm cable for Arduino Uno board<br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<USB30CMARD>

<Mini A - Micro USB B cable to connect a micro: bit card to a Texas Instruments TI-83 Premium CE Edition Python calculator<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<USB40TI>

<Boitier pour piles avec interrupteur<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<MBLOC3V>

<Connector for 9V batteries for powering an Arduino board<br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<COP9V>

<9V battery for powering an Arduino board<br><br><hr>This product is compatible with the following card(s) : <br> - Arduino Uno and Nano<br>>

<5000394082991>

<RFID tag combo (125khz) - 5 pcs<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<110990035>

<This prototyping kit is specific for micro:bit. It allows access on a seamless connection plate to the different ports of the micro:bit card. This kit contains: 4 machine screws with cylindrical head M3. 1 x stand 10 male to male jumper wires. 10 male to female jumper wires. 1 x seamless connection plate 1 x shield input / output connector for micro: bit<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br>>

<KITRO5609>

<Prototyping kit for Arduino board (not supplied) including: <br> - leds of various colors <br> - potentiometers <br> - ohmic conductors <br> - buttons <br> - Dupont male to male connection cables <br> - breadboard <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<KPROTOARD>

<Official case for Raspberry Pi 4 <br> Red and white color. Allows the protection of your Raspberry Pi4 card while providing easy access to the ports.<br><br><hr>This product is compatible with the following card(s) : <br> - QuickPi and RaspberryPi<br>>

<CASEOFFPI4>

<Official power supply for Raspberry Pi4 - USB type C. 15.3W European mains socket - Color: white<br><br><hr>This product is compatible with the following card(s) : <br> - QuickPi and RaspberryPi<br>>

<ALIMPI4>

<Official HDMI to mini HDMI cable for Raspberry Pi 4 Length 1 m, color white.<br><br><hr>This product is compatible with the following card(s) : <br> - QuickPi and RaspberryPi<br>>

<HDMIPi4>

<Official keyboard for Raspberry Pi <br> Fr-AZERTY keyboard in white / raspberry color. Includes 3 USB 2.0 Type A ports. <br> Compatible with all Raspberry Pi products.<br><br><hr>This product is compatible with the following card(s) : <br> - QuickPi and RaspberryPi<br>>

<KBOFF>

<Official wired mouse for Raspberry Pi <br> Includes 3 buttons and a dial.<br><br><hr>This product is compatible with the following card(s) : <br> - QuickPi and RaspberryPi<br>>

<MOOFF>

<MicroUsb to RJ45 LAN network adapter for RaspberryPi Zero WH. <br> This module allows you to add an ethernet socket on your RaspberryPi Zero WH card and thus benefit from the connection to the network.<br><br><hr>This product is compatible with the following card(s) : <br> - QuickPi and RaspberryPi<br>>

<ADAPRPIZERO>

<Adaptator microSD-USB<br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<SDUSB>

<This microSD card is ideal for recording data from sensors. Not suitable for recording photos or videos.>

<SD128MB>

<High performance 16GB MicroSDHC memory card. UHS-I Class 1 and Video Speed Class 10 (V10) specification Transfer speeds up to 100MB/s>

<SD16GB>

<6V box with switch for AAA batteries. >

<MBLOC6V>

<A small and compact USB Euro mains power supply suitable for charging USB powered devices. 5V 2.1A (10.5W)>

<ALIMSECTUSB>

<Rechargeable Li-Ion 3.7 V 650mAh battery in 16340 format protected against overcharging and discharging. <br> <br> Warning !<br> Due to airline regulatory reasons, this product cannot be exported.>

<ACCULIION16340>

<Rechargeable accumulator Li-ion 3.7 Vcc 2500 mAh in 18650 format. <br> Suitable for the feeding of the crawler aluminum chassis. <br> Attention! <br> For reasons of air regulation, this product can not be exported. <br>>

<INR18650-25R>

<Rechargeable Li-Ion 3.7 Vdc 800 mAh battery in 14500 format. <br> <br> Suitable for feeding the AlphaBot2 robot. <br> <br> Warning ! <br> For reasons of aviation regulations, this product cannot be exported. <br> <br> Reminder: precautions for using Li-lon batteries <br> - do not short-circuit or overcharge the battery (risk of explosion or fire) <br> - do not expose to too high temperatures <br> - only use a charger compatible with this type of batteries <br> - monitor the batteries during their recharging. If the temperature rises, stop the charging process <br> - do not place the batteries on a current conducting surface <br> - do not puncture the batteries <br> - respect the local sorting instructions <br>>

<ICR14500>

<Wheel + pneumatic adaptable to the continuously rotating servomotor. <br> Diameter: 60 mm </br> Thickness: 8 mm </br> Screw fixing included. </br>>

<FS90R-W>

<This case includes - an economical 30 W soldering iron - a desoldering pump - a cutter - miniature long nose pliers - miniature cutting pliers - 3 Phillips screwdrivers: 6 x 125 mm, 5 x 75 mm and 2.4 x 75 mm - 3 flat screwdrivers: 6 x 125 mm, 5 x 75 mm and 2.4 x 75 mm>

<KITOUTILS>

<HUE-HD Pro camera delivered with base, usb cable, manual and user license 1 station.>

<HUE-VIEWER-PRO>

<A plastic box with a resealable cover to store cards, sensors or other accessories. <br> Features removable dividers. <br> <br> Dimensions: 14 x 21cm <br>>

<3760327670191>

<Dedicated external battery to power the TI-Innovator Hub>

<03243480105668>

<Subscription to the Vittascience Premium platform with unlimited access for 1 teacher over 1 year. <br> Unlimited creation and sharing of activities <br> Access to the Vittascience resource bank <br> Automatic correction <br> Projects saved in the cloud <br> 1 teacher = 400 learners and 20 groups <br> Secure access via the GAR <br> 1h of shared support <br> Premium support - response within 24 working hours <br> <br><br><br><hr>This product is compatible with the following card(s) : <br> - Microbit<br> - QuickPi and RaspberryPi<br> - STM32 NUCLEI-WB55RG and NUCLEO-WL55<br> - Arduino Uno and Nano<br>>

<3760327670207>

<Gift card worth 30 € </br> </br> Can be used once in the Vittascience store, the card is valid for 1 year from purchase. </br> After purchase, you will receive it by email and can download and print it to give to loved ones. </br>>

<KDO30>

<>

<KDO50>

<Gift card worth 100 € </br> </br> Can be used once in the Vittascience store, the card is valid for 1 year from purchase. </br> After purchase, you will receive it by email and can download and print it to give to loved ones. </br>>

<KDO100>

<Gift card worth 150 € </br> </br> Can be used once in the Vittascience store, the card is valid for 1 year from purchase. </br> After purchase, you will receive it by email and can download and print it to give to loved ones. </br>>

<KDO150>

<Gift card worth 200 € </br> </br> Can be used once in the Vittascience store, the card is valid for 1 year from purchase. </br> After purchase, you will receive it by email and can download and print it to give to loved ones. </br>>

<KDO200>